Will a crappy one add noise tho ?
A basic Limiter
-
- tower block dreamin
- Posts: 361
- Joined: Sat Feb 18, 2017 5:56 pm
-
- proppa neck!
- Posts: 2784
- Joined: Tue Apr 05, 2016 1:23 am
Re: A basic Limiter
No. You're putting in AC from a small transformer. Any rubbish will be filtered by the DC side of the circuit - the smoothing capacitors after the rectifier diodes and the regulators will keep things stable. A simple PSU like that (as used widely in professional audio gear) is easy to build, but very effective.
"Why is my rig humming?"
"Because it doesn't know the words!"
"Because it doesn't know the words!"
-
- who u callin ne guy bruv
- Posts: 27
- Joined: Tue Oct 04, 2016 6:36 pm
Re: A basic Limiter
Does the aluminum electrolytic cap work as well as the tantalum in the circuit? Any issues?sinus trouble wrote: ↑Tue Apr 18, 2017 11:16 pm R-3M9 and 1uf TANTALUM should control release time (small/moderate delay)
-
- proppa neck!
- Posts: 2784
- Joined: Tue Apr 05, 2016 1:23 am
Re: A basic Limiter
Yes - you're not looking for long delay times, so a conventional electrolytic will usually be OK. My limiters use conventional electrolytics throughout - I've never really liked tantalum beads!
"Why is my rig humming?"
"Because it doesn't know the words!"
"Because it doesn't know the words!"
- sinus trouble
- proppa neck!
- Posts: 1410
- Joined: Fri Aug 22, 2014 11:34 pm
Re: A basic Limiter
Yes my statement may have been a bit misleading? There was a time Tantalum was considered more stable than electrolytics? But with todays technology, little or significant difference is rarely seen.EFIALTISFM wrote: ↑Fri Jan 28, 2022 10:02 pmDoes the aluminum electrolytic cap work as well as the tantalum in the circuit? Any issues?sinus trouble wrote: ↑Tue Apr 18, 2017 11:16 pm R-3M9 and 1uf TANTALUM should control release time (small/moderate delay)
Also remember that these components can be 'user defined' They simply control how long the limiter holds active!
For example? Fast release times can cause 'Pumping' sounds! Slower release times can generally create a more 'levelled' sound but detrimental to the overall 'loudness'
So you need to get that happy medium? If that makes sense?
I am as stupid as I look!
-
- who u callin ne guy bruv
- Posts: 27
- Joined: Tue Oct 04, 2016 6:36 pm
Re: A basic Limiter
Hi Albert,
Two questions...
1. The board labeling for the FET has it as a DGS but the 2n5457 is a DSG so is this a typographical error or should track 22 and 23 be switched the around?
2. You've mentioned feeding the audio in through a 100k log pot. Is the pot in addition to the existing 47k resistor or by replacing it?
Ta
-
- proppa neck!
- Posts: 2784
- Joined: Tue Apr 05, 2016 1:23 am
Re: A basic Limiter
There is a fundamental error in that design as shown. It's actually two mono limiters, working independently. If the limiting action isn't the same in both channels, the stereo image will be seriously messed up!I'd recommend something more proper, with a low noise and distortion VCA such as the circuit in the following link: http://sbpcb.blogspot.it/2012/12/stereo ... s.html?m=1
I've built limiters (and compressors) using the 2081 (and 2180) VCA chips, and the results can be exceptionally good. I added the left and right inputs together through a couple of op-amp buffers to feed a common sidechain I built a bargraph indicator to monitor the VCA control voltage, thereby showing the amount of gain reduction being applied. My sidechain used full-wave rectification of the audio (using an "ideal diode" op-amp circuit), and the time constants for attack and decay were "program dependent", making the operation of the limiter less obvious to the ear. Without using delay line methods, the basic limiter is prone to overshoots - it can (effectively) reduce the audio too much, causing a post-peak "gap" as the gain recovers to normal. This can be minimised by sensible choice of time constants, but will always be a compromise with a basic limiter, and you'll always need a post-limiter clipper to prevent over deviation on peaks.
A more sophisticated approach - without "going digital" - is to introduce a delay into the audio path, with the sidechain take-offs before the delay, and the VCAs after the delay. With the right selection of delay (roughly the same as the attack time of your limiter), you can eliminate overshoots and pumping whilst keeping really tight control of level. This is so good that it obviates the need for a clipper after the limiter to prevent sudden peaks getting through!
The classic delay line topology - as used in the 1970s Pye broadcast limiters - used capacitive and inductive "all-pass" networks, cascaded to provide a flat frequency response over the audio range. This was incredibly expensive and required dozens of custom-wound coils. My approach is to use "bucket-brigade" delay ICs, overclocked to give a very wide bandwidth and to move the clock noise (and other artefacts) well into the ultrasonic. I used MN3007 ICs (they have to be genuine Panasonic ones) clocked at about 410kHz for about 1¼ms delay, with the sidechain attack time constant set at the same..... In use, the delay is imperceptible - it's just like the monitor speakers being (roughly) 13" further from the listener! On headphones, you can't notice the delay between your speech and it appearing in your ears!
Practically speaking, the MN3007 S/N ratio is slightly over 80dB, which is not much worse than the rest of the audio chain, all noise sources considered. Its distortion is also not too bad - and much better than the distortion introduced by clipping if it's needed!
"Why is my rig humming?"
"Because it doesn't know the words!"
"Because it doesn't know the words!"
-
- proppa neck!
- Posts: 2784
- Joined: Tue Apr 05, 2016 1:23 am
Re: A basic Limiter
The pot is additional - the wiper feeds the input resistor.EFIALTISFM wrote: ↑Sat Feb 12, 2022 10:35 pmHi Albert,
Two questions...
1. The board labeling for the FET has it as a DGS but the 2n5457 is a DSG so is this a typographical error or should track 22 and 23 be switched the around?
2. You've mentioned feeding the audio in through a 100k log pot. Is the pot in addition to the existing 47k resistor or by replacing it?
Ta
I can't remember the FETs I used to use - they were DGS pinout. Just rotate your FET so that the legs are the right way 'round!
"Why is my rig humming?"
"Because it doesn't know the words!"
"Because it doesn't know the words!"
- sinus trouble
- proppa neck!
- Posts: 1410
- Joined: Fri Aug 22, 2014 11:34 pm
Re: A basic Limiter
EFIALTIFM
I think you will be good to go with pretty much any FET? Im sure they will perform reasonable enough!
Many 'Vintage' Audio amplifiers i have repaired often needed some manipulation of driver transistor leads to get modern replacements to fit!
I think you will be good to go with pretty much any FET? Im sure they will perform reasonable enough!
Many 'Vintage' Audio amplifiers i have repaired often needed some manipulation of driver transistor leads to get modern replacements to fit!
I am as stupid as I look!
-
- who u callin ne guy bruv
- Posts: 27
- Joined: Tue Oct 04, 2016 6:36 pm
Re: A basic Limiter
Hi Albert,
Thanks for your feedback.
Just completed the kit and tested but got a problem. Audio starts and then stops and then starts and stops again and so on. All this within 3 seconds.
Any thoughts what might be causing this?
-
- who u callin ne guy bruv
- Posts: 27
- Joined: Tue Oct 04, 2016 6:36 pm
Re: A basic Limiter
Thanks sinus.sinus trouble wrote: ↑Mon Feb 14, 2022 12:00 am EFIALTIFM
I think you will be good to go with pretty much any FET? Im sure they will perform reasonable enough!
Many 'Vintage' Audio amplifiers i have repaired often needed some manipulation of driver transistor leads to get modern replacements to fit!
Used a 2N5457 but had to switch round the SG legs to fit the boards layout (as suggested by Albert).
The kit has been assembled but got an issue when audio starts (I've asked for Alberts advice in my previous message)
-
- who u callin ne guy bruv
- Posts: 27
- Joined: Tue Oct 04, 2016 6:36 pm
Re: A basic Limiter
Here are some photos of the kit
-
- proppa neck!
- Posts: 919
- Joined: Fri Aug 26, 2016 7:01 pm
Re: A basic Limiter
bf245/bf244 could replace bf256 ?
- rigmo
- tower block dreamin
- Posts: 472
- Joined: Wed Jan 30, 2019 9:35 pm
Re: A basic Limiter
This site can’t be reachedAlbert H wrote: ↑Sat Apr 22, 2017 10:27 am
If you take a look at http://sound.whsites.net/project67.htm to see a limiter that's nearly the same - Rod Elliott obviously went to the same school as LB! Rod's article explains the operation of the gain cell and the steps taken to minimise distortion (I think that LB pinched Rod's values when he did his PCB).
- thewisepranker
- proppa neck!
- Posts: 569
- Joined: Fri Aug 22, 2014 12:53 pm
- Location: Brighton
Re: A basic Limiter
Rod had to move host (and therefore domain) as Westhost supposedly screwed him over. New link: https://sound-au.com/project67.htm
-
- tower block dreamin
- Posts: 361
- Joined: Sat Feb 18, 2017 5:56 pm
Re: A basic Limiter
A friend asks if there is a pcb available ? As he wants to try it. Personally I use Breakaway One which is an awesome processor for the cost.
Will you be selling kits on eBay if they are made a little more pro with nice laid out pc, maybe even nicer built versions not just kits ? kits could be £40 and built £60. ? Or anyone else better ideas?
Will you be selling kits on eBay if they are made a little more pro with nice laid out pc, maybe even nicer built versions not just kits ? kits could be £40 and built £60. ? Or anyone else better ideas?
Sony ST 920 QS
- sinus trouble
- proppa neck!
- Posts: 1410
- Joined: Fri Aug 22, 2014 11:34 pm
Re: A basic Limiter
The problem with 'Limiters' is that there are no 'perfect settings'
Especially with Pirate radio! Content is usually taken from a vast number of sources which will have different dynamics!
A show takes a lot of pre preparation to get it right! The work you put in FIRST will produce better results!
My advice would be to process your audio media as best you can before even thinking of going LIVE! (Levelling up etc...)
The 'Limiter' should be a last resort for protection!
Especially with Pirate radio! Content is usually taken from a vast number of sources which will have different dynamics!
A show takes a lot of pre preparation to get it right! The work you put in FIRST will produce better results!
My advice would be to process your audio media as best you can before even thinking of going LIVE! (Levelling up etc...)
The 'Limiter' should be a last resort for protection!
I am as stupid as I look!
- mpx
- tower block dreamin
- Posts: 251
- Joined: Mon Dec 23, 2019 9:49 am
Re: A basic Limiter
How about a raspberry pi running stereo tool
-
- proppa neck!
- Posts: 2784
- Joined: Tue Apr 05, 2016 1:23 am
Re: A basic Limiter
Unfortunately, unless you use a Pi 4, the R Pi doesn't have enough "grunt". Stereotool is a Windoze application - the R Pi runs Linux....
I've been experimenting with a R P1 3B+ and a sound card for audio processing. The sound card I used is an "AudioInjector" (and Australian project) and used streamed audio input, using DarkIce as the audio streamer.... Results are getting good, but it's not ready for serious use yet.....
I've been experimenting with a R P1 3B+ and a sound card for audio processing. The sound card I used is an "AudioInjector" (and Australian project) and used streamed audio input, using DarkIce as the audio streamer.... Results are getting good, but it's not ready for serious use yet.....
"Why is my rig humming?"
"Because it doesn't know the words!"
"Because it doesn't know the words!"
-
- who u callin ne guy bruv
- Posts: 18
- Joined: Tue Jun 09, 2015 11:06 am
Re: A basic Limiter
Hi,
I build this processor with the original 2N5459 but used the SMD version MMBF5459.
It works perfectly, so I build a second version, but I was forced to use a 2N5458 which I thought is a replacement that should work.
However, this version only amplifies the signal (compressing) but no limiting.
The orange peak led is ON all the time. It does not blink when I put audio into it.
Can this be caused by the 2N5458?
I check the print over and over again if I made any other mistakes.
I build this processor with the original 2N5459 but used the SMD version MMBF5459.
It works perfectly, so I build a second version, but I was forced to use a 2N5458 which I thought is a replacement that should work.
However, this version only amplifies the signal (compressing) but no limiting.
The orange peak led is ON all the time. It does not blink when I put audio into it.
Can this be caused by the 2N5458?
I check the print over and over again if I made any other mistakes.