Page 2 of 3

Re: Link Receiver

Posted: Sun Jan 28, 2018 2:43 am
by Albert H
Been away - very busy - then I got 'flu. I've been laid up for 8 days!

Re: Link Receiver

Posted: Sun Jan 28, 2018 8:02 am
by radium98
Oh i am sorry .please when u been in a good health try to post it i just wanna give a try or remove a stage from it not more

Re: Link Receiver

Posted: Tue Jun 26, 2018 1:07 pm
by OldskoolPirate
Albert can you post the pcb you said about. I want to give this a go. Thanks

Re: Link Receiver

Posted: Wed Jun 27, 2018 11:53 pm
by Albert H
I'll be at my desk early next week. I'll post all the details then for you.

I've also done some work on reproducing the old Toko S18 series of coils, using a 3D printer for the former. My home-made coils are better than the originals! I will put up the code for anyone else who wants to make them.

Re: Link Receiver

Posted: Thu Jun 28, 2018 1:26 pm
by OldskoolPirate
There are loads under different part numbers. 10.7mhz 82pf

Re: Link Receiver

Posted: Fri Jun 29, 2018 3:06 pm
by Albert H
The Toko S18 series of coils were the standard parts used by everyone, as they were stable, cheap and gave reproducible results. They had a plastic former and were wound with silvered copper wire. The colour of plastic denoted the number of turns!

My old rigs in the 80s used a violet one for the VCO with an aluminium slug (it was very stable even without a PLL) at half frequency, then another violet one in the buffer stage, and yellow ones in the doubler and filter stages. All the subsequent coils (except chokes) were self-supporting air-cored, usually wound with enamelled copper wire. I used to use reverse-biased green LEDs for the VCO tuning, and reverse-biased 1N4001 for the modulation. These were much cheaper than proper "varicap" diodes and gave great results.

The early stages used BF494 transistors to get to 100mW, all running at 15V, then a three-stage PA with a 2N3866 into a 2N3375, then a 587BLY for around 95 Watts, all running on about 30V. The only expensive parts were the output capacitors, the smoothing capacitor, the heatsink and the mains transformer. These rigs - which were used by loads of stations - were clean, stable and reasonably idiot-proof!

They went on to three PCBs - exciter /PLL, PA and PSU. The boards were double-sided, and made as a single board, which was cut up. There were three versions, early - using 74LS logic and diode programming, middle - using a Plessey prescaler and CMOS logic, and the final version using a Philips all-in-one PLL chip and a PIC! The rig was meant to be as cheap as possible. Parts price was around £30 in 1982. Each had a concealed serial number and we made just over 1200 of them over the years. There were a couple of other variants - just higher or lower power - and we made about 500 of those. Other "builders" would often sell them on as their own work!

I was pleased recently to discover a station in Italy still using two of them after nearly 40 years!

Re: Link Receiver

Posted: Wed Jul 04, 2018 3:09 pm
by OldskoolPirate
Any pcb for this yet ? Otherwise I’m gonna have to sit there for hours and draw it all out lol.

Re: Link Receiver

Posted: Thu Jul 05, 2018 12:08 am
by MC Spanner
I've a vague idea someone sent Harry Lythall a scrappy looking hand drawn design for a Band I receiver and he published it. The idea was similar to the one at the top of this thread and I don't remember it using Toko cans etc. The mixer transformer and tank coil on the 3189E were hand wound, with instructions. A search should turn it up. I think it was this design built "dead bug" style of which there used to be a picture on Stephen Moss's website. I used to see a lot of Band I gear built dead bug stylee back in the day :roll:

There's also the Bowman design kicking around the web and it had a PCB layout in the release notes but pretty sure it uses Toko cans so you'll have the same problem.

Enigma still had some OEM S18 coils last I looked.

Re: Link Receiver

Posted: Thu Jul 05, 2018 2:37 pm
by radium98
@ MC Spanner i think you speak about this
http://213.114.131.21/_visitors/rx/linkrx.htm
i hope someone will make a design layout because i dont think that the one one that albert talk about will be published it will been taken a looong time
http://www.gareth.net.nz/nrgworkshop/ty ... ircuit.jpg

Re: Link Receiver

Posted: Fri Jul 06, 2018 12:00 am
by MC Spanner
radium98 wrote: Thu Jul 05, 2018 2:37 pmit will been taken a looong time
Yes - long enough for you to have drawn up the layout yourself! It's not rocket science.

Re: Link Receiver

Posted: Fri Jul 06, 2018 11:15 am
by THE GOVERNOR
MC Spanner wrote: Thu Jul 05, 2018 12:08 am There's also the Bowman design kicking around the web and it had a PCB layout in the release notes but pretty sure it uses Toko cans so you'll have the same problem.
Band1_Receiver.jpg

Re: Link Receiver

Posted: Fri Jul 06, 2018 10:43 pm
by sinus trouble
I think I have uploaded this before? I still have an original bowman here! Often thought of reproducing it but couldn't identify the TOKOs the diagram does show the PCB connections and if I remember correct, the input coils are just standard trimmers with a couple of turns of copper wire wrapped around?
Bowman B1RX.JPG

Re: Link Receiver

Posted: Sun Jul 08, 2018 10:25 am
by radium98
Thank you MC Spanner for clarifying that to me ,i do not know what to do without you and without youre valuable answer if you do not saying that to me .

Re: Link Receiver

Posted: Sun Jul 08, 2018 1:35 pm
by MC Spanner
radium98 wrote: Sun Jul 08, 2018 10:25 ami do not know what to do
:roll:

Re: Link Receiver

Posted: Mon Jul 09, 2018 12:14 am
by Albert H
A friend of mine has taken to hacking cheap transistor radio boards for Band I receivers. He buys a "Philips" brand radio, removes the PCB from the case, pads down the local oscillator to get it to around 70 MHz, replaces the input filter coils and capacitors, removes the telescopic rod aerial, and mounts the PCB into an aluminium box. The aerial input is through a BNC connector, and the audio / multiplex output is through a phono socket. There's also a "tuned" indicator LED, and he adds an LM311 comparator and a relay for carrier detection. There's also a muting transistor that shorts the audio output when no signal is received. These things are free-running oscillator jobs (no PLL) but have AFC (automatic frequency control) that locks the receiver to the incoming signal. His link transmitter is very simple, with a 30MHz free-running Colpitts oscillator, doubler and two stages of amplification up to a couple of Watts. It doesn't matter if the link transmitter drifts a bit, because the receiver will follow it!

Re: Link Receiver

Posted: Sat Apr 15, 2023 1:33 am
by XXL
sinus trouble wrote: Fri Jul 06, 2018 10:43 pm I think I have uploaded this before? I still have an original bowman here! Often thought of reproducing it but couldn't identify the TOKOs the diagram does show the PCB connections and if I remember correct, the input coils are just standard trimmers with a couple of turns of copper wire wrapped around?

Bowman B1RX.JPG
Anyone have the parts list for this ?

Re: Link Receiver

Posted: Sat Apr 15, 2023 1:35 am
by XXL
This one!
B57C56A5-BDCF-450C-86BF-D5FB155B11BA.png

Re: Link Receiver

Posted: Sat Apr 15, 2023 4:11 am
by Albert H
Good luck finding a genuine TDA1062 at a reasonable price these days.

As I posted a while ago, it's easy to hack a cheap transistor radio!

Re: Link Receiver

Posted: Mon Apr 17, 2023 1:37 am
by XXL
some fake parts are just as good. but no chance of building this without the parts list :(

Re: Link Receiver

Posted: Mon Apr 17, 2023 7:14 am
by radium98
tda1062 no equivalent , but if you know how it work , you may rerplace it . If i want to build one , i prefer the sinus 1 as good as simple , may need extra notch filter if there is stong rf signal around , but it is not synthesized